Baseline Encoding and Transport of Pre-Congestion Information
draft-ietf-pcn-baseline-encoding-00

Status of this Memo

By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.

This Internet-Draft will expire on April 3, 2009.

Abstract

Pre-congestion notification (PCN) provides information to support admission control and flow termination in order to protect the Quality of Service of inelastic flows. It does this by marking packets when traffic load on a link is approaching or has exceeded a threshold below the physical link rate. This document specifies how such marks are to be encoded into the IP header. The baseline encoding described here provides for only two PCN encoding states. It is designed to be easily extensible to provide more encoding states but such schemes will be described in other documents.

Table of Contents

1.  Introduction
2.  Requirements notation
3.  Terminology
4.  Encoding two PCN States in IP
    4.1.  Rationale for Encoding
    4.2.  PCN-Compatible DiffServ Codepoints
5.  Backwards Compatability
6.  IANA Considerations
7.  Security Considerations
8.  Conclusions
9.  Acknowledgements
10.  Comments Solicited
11.  References
    11.1.  Normative References
    11.2.  Informative References
Appendix A.  Tunnelling Constraints
Appendix B.  PCN Node Behvaiours
    B.1.  Valid and Invalid Encoding Transitions at a PCN Node
Appendix C.  Deployment Scenarios for PCN Using Baseline Encoding
§  Authors' Addresses
§  Intellectual Property and Copyright Statements

1.  Introduction

Pre-congestion notification (PCN) provides information to support admission control and flow termination in order to protect the quality of service (QoS) of inelastic flows. This is achieved by marking packets according to the level of pre-congestion at nodes within a PCN-domain. These markings are evaluated by the egress nodes of the PCN-domain. [PCN‑arch] (Eardley, P., “Pre-Congestion Notification Architecture,” February 2008.) describes how PCN packet markings can be used to assure the QoS of inelastic flows within a single DiffServ domain.

This document specifies how these PCN marks are encoded into the IP header. It also describes how packets are identified as belonging to a PCN flow. Some deployment models require two PCN encoding states, others require more. The baseline encoding described here only provides for two PCN encoding states. An extension of the baseline encoding described in [PCN‑3‑enc‑state] (Moncaster, T., Briscoe, B., and M. Menth, “A three state extended PCN encoding scheme,” June 2008.) provides for three PCN encoding states. Other extensions have also been suggested all of which can build on the baseline encoding.

Changes from previous drafts (to be removed by the RFC Editor):

From -02 to -03:

Minor changes throughout.

Modified meaning of ECT(1) state to EXP.

Moved text relevant to behaviour of nodes into appendix for later transfer to new document on edge behaviours

From -01 to -02:

Minor changes throughout including tightening up language to remain consistent with the PCN Architecture terminology

From -00 to -01:

Change of title from "Encoding and Transport of (Pre-)Congestion Information from within a DiffServ Domain to the Egress"

Extensive changes to Introduction and abstract.

Added a section on the implications of re-using a DSCP.

Added appendix listing possible operator scenarios for using this baseline encoding.

Minor changes throughout.

2.  Requirements notation

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).

3.  Terminology

The following terms are used in this document:

• Not-PCN - packets that are not PCN capable.
• PCN-marked - codepoint indicating packets that have been marked at a PCN-interior-node using some PCN marking behaviour. Also PM.
• Not-Marked - codepoint indicating packets that are PCN capable but are not PCN-marked. Also NM.
• PCN-enabled codepoints - collective term for all the NM and PM codepoints.
• PCN-compatible Diffserv codepoint - a Diffserv codepoint for which the ECN field is used to carry PCN markings rather thatn [RFC3168] (Ramakrishnan, K., Floyd, S., and D. Black, “The Addition of Explicit Congestion Notification (ECN) to IP,” September 2001.) markings.

In addition the document uses the terminology defined in [PCN‑arch] (Eardley, P., “Pre-Congestion Notification Architecture,” February 2008.).

4.  Encoding two PCN States in IP

The PCN encoding states are defined using a combination of the DSCP and ECN fields within the IP header. The baseline PCN encoding closely follows the semantics of ECN [RFC3168]. It allows the encoding of two PCN states: Not-Marked and PCN-Marked. It also allows for traffic that is not PCN capable to be marked as such (not-PCN). Given the scarcity of codepoints within the IP header the baseline encoding leaves one codepoint free for experimental use. The following table defines how to encode these states in IP:

Where DSCP n is a PCN-enabled DiffServ codepoint (see Section 4.2 (PCN-Compatible DiffServ Codepoints)) and EXP means available for Experimental use.

The following rules apply to all PCN traffic:

• PCN traffic MUST be marked with a PCN-compatible DiffServ Codepoint. That is a DiffServ codepoint that indicates that PCN could be enabled by setting the appropriate value in the ECN field. To conserve DSCPs, DiffServ Codepoints SHOULD be chosen that are already defined for use with admission controlled traffic, such as the Voice-Admit codepoint defined in [voice‑admit] (Baker, F., Polk, J., and M. Dolly, “DSCPs for Capacity-Admitted Traffic,” February 2008.).
• Any packet that is not PCN-enabled (not-PCN) but which shares the same DiffServ codepoint as PCN-enabled traffic MUST have the ECN field set to 00.

4.1.  Rationale for Encoding

The exact choice of encoding was dictated by the constraints imposed by existing IETF RFCs, in particular [RFC3168] (Ramakrishnan, K., Floyd, S., and D. Black, “The Addition of Explicit Congestion Notification (ECN) to IP,” September 2001.) and [RFC4774] (Floyd, S., “Specifying Alternate Semantics for the Explicit Congestion Notification (ECN) Field,” November 2006.). Full details are contained in [pcn‑enc‑compare] (Chan, K., Karagiannis, G., Moncaster, T., Menth, M., Eardley, P., and B. Briscoe, “Pre-Congestion Notification Encoding Comparison,” February 2008.). One of the tightest constraints was the need for any PCN encoding to survive being tunnelled through either an IP in IP tunnel or an IPSec Tunnel. Appendix A (Tunnelling Constraints) explains this in detail. The main effect of this constraint is that any PCN marking has to use the ECN field set to 11 (CE codepoint). If the packet is being tunneled then only the CE codepoint gets copied into the inner header upon decapsulation. An additional constraint is the need to minimise the use of DiffServ codepoints as these are in increasingly short supply. Section 4.2 (PCN-Compatible DiffServ Codepoints) explains how we have minimised this still further by reusing pre-existing Diffserv codepoint(s) such that non-PCN traffic can still be distinguished from PCN traffic.

The encoding scheme (Table 1 (Encoding PCN in IP)) that best addresses the above constraints ends up looking very similar to ECN. This is perhaps not surprising given the similarity in architectural intent between PCN and ECN.

4.2.  PCN-Compatible DiffServ Codepoints

Equipment complying with the baseline PCN encoding MUST allow PCN to be enabled for a certain Diffserv codepoint or codepoints. This document defines the term "PCN-Compatible Diffserv Codepoint" for such a DSCP. Enabling PCN for a DSCP switches on PCN marking behaviour for packets with that DSCP, but only if those packets also have their ECN field set to indicate a codepoint other than not-PCN.

Enabling PCN marking behaviour disables any other marking behaviour (e.g. enabling PCN disables the default ECN marking behaviour introduced in [RFC3168] (Ramakrishnan, K., Floyd, S., and D. Black, “The Addition of Explicit Congestion Notification (ECN) to IP,” September 2001.)). The scheduling behaviour is discussed in [pcn‑marking‑behaviour] (Eardley, P., “Marking behaviour of PCN-nodes,” June 2008.).

5.  Backwards Compatability

BCP 124 [RFC4774] (Floyd, S., “Specifying Alternate Semantics for the Explicit Congestion Notification (ECN) Field,” November 2006.) gives guidelines for specifying alternative semantics for the ECN field. It sets out a number of factors that must be taken into consideration. It also suggests various techniques to allow the co-existence of default ECN and alternative ECN semantics. The baseline encoding specified in this document defines PCN-compatible DiffServ Codepoints as no longer supporting the default ECN semantics. As such this document is compatible with BCP 124.

6.  IANA Considerations

This document makes no request to IANA.

7.  Security Considerations

Packets claim entitlement to be PCN marked by carrying a PCN-enabled DSCP and a PCN-Capable ECN codepoint. This encoding document is intended to stand independently of the architecture used to determine whether specific packets are authorised to be PCN marked, which will be described in a future separate document on PCN edge-node behaviour (see Appendix B (PCN Node Behvaiours)).

The PCN working group has initially been chartered to only consider a PCN-domain to be entirely under the control of one operator, or a set of operators who trust each other [PCN‑charter] (IETF, “IETF Charter for Congestion and Pre-Congestion Notification Working Group,” .). However there is a requirement to keep inter-domain scenarios in mind when defining the PCN encoding. One way to extend to multiple domains would be to concatenate PCN-domains and use PCN-boundary-nodes back to back at borders. Then any one domain's security against its neighbours would be described as part of the edge-node behaviour document as above.

One proposal on the table allows one to extend PCN across multiple domains without PCN-boundary-nodes back-to-back at borders [re‑PCN] (Briscoe, B., “Emulating Border Flow Policing using Re-ECN on Bulk Data,” July 2007.). It is believed that the encoding described here would be compatible with the security framework described there.

8.  Conclusions

This document defines the baseline PCN encoding utilising a combination of a PCN-enabled DSCP and the ECN field in the IP header. This baseline encoding allows the existence of two PCN encoding states, not-Marked and PCN-Marked. It also allows for the co-existence of traffic that is not PCN-capable within the same DSCP so long as theat traffic doesn't require end-to-end ECN support. The encoding scheme is conformant with [RFC4774] (Floyd, S., “Specifying Alternate Semantics for the Explicit Congestion Notification (ECN) Field,” November 2006.).

9.  Acknowledgements

This document builds extensively on work done in the PCN working group by Kwok Ho Chan, Georgios Karagiannis, Philip Eardley and others. Full details of the alternative schemes that were considered for adoption can be found in the document [pcn‑enc‑compare] (Chan, K., Karagiannis, G., Moncaster, T., Menth, M., Eardley, P., and B. Briscoe, “Pre-Congestion Notification Encoding Comparison,” February 2008.). Thanks to Ruediger Geib for providing detailed comments on this document.

10.  Comments Solicited

Comments and questions are encouraged and very welcome. They can be addressed to the IETF congestion and pre-congestion working group mailing list <pcn@ietf.org>, and/or to the authors.

11.  References

11.1. Normative References

11.2. Informative References

Appendix A.  Tunnelling Constraints

The rules that govern the behaviour of the ECN field for IP-in-IP tunnels were defined in [RFC3168] (Ramakrishnan, K., Floyd, S., and D. Black, “The Addition of Explicit Congestion Notification (ECN) to IP,” September 2001.). This allowed for two tunnel modes. The limited functionality mode sets the outer header to not-ECT, regardless of the value of the inner header, in other words disabling ECN within the tunnel. The full functionality mode copies the inner ECN field into the outer header if the inner header is not-ECT or either of the 2 ECT codepoints. If the inner header is CE then the outer header is set to ECT(0). On decapsulation, if the CE codepoint is set on the outer header then this is copied into the inner header. Otherwise the inner header is left unchanged. The stated reason for blocking CE from being copied to the outer header was to prevent this from being used as a covert channel through IPSec tunnels.

The IPSec protocol [RFC4301] (Kent, S. and K. Seo, “Security Architecture for the Internet Protocol,” December 2005.) changed the ECN tunnelling rule to allow IPSec tunnels to simply copy the inner header into the outer header. On decapsulation the outer header is discarded and the ECN field is only copied down if it is set to CE.

Because of the possible existence of tunnels, only CE (11) can be used as a PCN marking as it is the only mark that will survive decapsulation. However there is a need for caution with all tunneling within the PCN-domain. RFC3168 full functionality IP in IP tunnels are expected to set the ECN field to ECT(0) if the inner ECN field is set to CE. This leads to the possibility that some packets within the PCN-domain that have already been marked may have that mark concealed further into the domain. This is undesirable for many PCN schemes and thus standard IP in IP tunnels SHOULD NOT be used within a PCN-domain. Further work is needed within the Transport Area to rationalise the behaviour of IP in IP tunnels in respect to the ECN field and bring them in line with the behaviour of IPSec tunnels [ecn‑tunnelling] (Briscoe, B., “Layered Encapsulation of Congestion Notification,” July 2008.).

Appendix B.  PCN Node Behvaiours

Any packet that belongs to a PCN capable flow MUST have the ECN field set to indicate a NM state at the PCN-ingress-node.

Any packet that is PCN capable and has been PCN-marked by a PCN-interior-node MUST have the ECN field set to indicate a PM state.

Any packet leaving the PCN-domain SHOULD have the ECN field reset to 00. The only exception is where the egress node knows the end-hosts will react safely to any PCN marks they receive.

B.1.  Valid and Invalid Encoding Transitions at a PCN Node

• PCN-interior-nodes MUST NOT change not-PCN to another codepoint and they SHOULD NOT change a PCN-Capable codepoint to not-PCN except where they need to downgrade the packet to a lower class of service.
• PCN-interior-nodes that are in a pre-congestion state above the configured level MUST set a PM codepoint as defined in Table 1 (Encoding PCN in IP) or in any local/experimental scheme running within the PCN-domain.
• Packets carrying the 01 ECT(1) codepoint are for local/experimental use only and their unexpected presence SHOULD cause an alarm to be raised at the management level. However, to allow for the possibility of misconfiguration they SHOULD be treated as NM packets.
• The PM codepoint MUST NOT be changed to NM.

Appendix C.  Deployment Scenarios for PCN Using Baseline Encoding

This appendix illustrates possible PCN deployment scenarios where the baseline encoding can be used and also explain a case for which baseline encoding is not sufficient. {Note this appendix is provided for information only}.

1. An operator may wish to use PCN-based admission control only. To that end, threshold marking based on admissible rates might be used as the only PCN metering and marking algorithm. As a consequence, the PM marks on the packets are interpreted as meaning the ingress should stop admitting new traffic.
2. An operator may wish to use PCN-based flow termination only. To that end, excess rate marking based on supportable rates might be used as the only PCN metering and marking algorithm. As a consequence, the PM marks on the packets are interpreted as meaning the ingress shoudl start terminating appropriate flows.
3. An operator may wish to use both PCN-based admission control and flow termination. To that end, excess rate marking based on admissible rates might be used as the only PCN metering and marking algorithm. The level of marks will be used to determine when the ingress shoudl stop admitting new traffic and whether the ingress should terminate any flows.
4. An operator may wish to implement admission control based on threshold marking at admissible rates and flow termination based on excess rate marking at supportable rates because these methods are believed to work better with small ingress-egress aggregates. Then two different markings are needed. Such a deployment scenario is not supported by the PCN baseline encoding.

Authors' Addresses

Full Copyright Statement

Copyright © The IETF Trust (2008).

This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.

This document and the information contained herein are provided on an “AS IS” basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.

Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.

The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.

Acknowledgment

This document was produced using xml2rfc v1.33 (of http://xml.resource.org/) from a source in RFC-2629 XML format.